Iblit
Iblit is a VST 2.0 compatible monophonic software synthesizer.
Programmed by Andreas Ersson ers@bostreammail.net.
Copyright ⌐ 2002 Andreas Ersson
VST is a trademark of Steinberg Soft- und Hardware GmbH
Oscillator
Parameters
Wave
Sets the oscillator output waveform.Saw/Pulse.
Transpose
The oscillators can be individually transposed.Range: ▒24 semitones.
Fine Tune
Detunes the oscillator.Range: ▒50cent.
Lfo Mod
Controls the LFO (LFO Osc) modulation of the oscillator frequency.Range: 0-100%
Pw
Sets the pulse width of the oscillator when Wave is set to Pulse.Range: 10-90%
Lfo Pwm
Controls the LFO modulation (LFO Osc) of the pulse width when Wave is set to Pulse.Range: 0-100%
Mixer
Parameters
Osc 1 On/Off
Turns on and off oscillator 1.Range: On/Off
Osc 1 Level
Sets the output level of oscillator 1.Range: -30dB-+6dB
Osc 2 On/Off
Turns on and off oscillator 2.Range: On/Off
Osc 2 Level
Sets the output level of oscillator 2.Range: -30dB-+6dB
Osc 3 On/Off
Turns on and off oscillator 1.Range: On/Off
Osc 3 Level
Sets the output level of oscillator 3.Range: -30dB-+6dB
Noise On/Off
Turns on and off the noise generator.Range: On/Off
Noise Level
Sets the output level of noise generator.Range: -30dB-+6dB
DCF
Parameters
Type
Sets the type of filter.LP(Low Pass) or HP(High Pass).
Cutoff
Sets the cutoff frequency of the filter.Range: 20Hz-16.2kHz
Q
Sets the Q (resonance) of the filter.Range: 0.5-20
Env Depth
Controls how much the envelope (Env1) will affect the cutoff frequency.Range: ▒100%
Lfo Depth
Controls the LFO (Lfo Dcf) modulation of the cutoff frequency.Range: 0-100%
Norm
Filter Normalization.When activated the output of the filter is normalized at the cutoff frequency.
Range: On/Off
DCA
Parameters
Volume
Sets the output volume.Range: -30dB-+6dB
Envelope Generator
Envelope 1 (Env1) is connected to the DCF and envelope 2 (Env2) is connected to the DCA.Parameters
Attack
Sets the attack time of the envelope.Range: 1ms-5s
Decay
Sets the decay time of the envelope.Range: 5ms-4s
Sustain
Sets the sustain level of the envelope.Range: 0-100%
Release
Sets the release time of the envelope.Range: 5ms-3s
LFO
There are two LFOs in the Iblit.Lfo Osc is connected to the oscillators and Lfo Dcf is connected to the DCF.
Parameters
Wave
Sets the output waveform of the LFO.Sin/Saw/Tri/Square/S/H
Speed
Sets the LFO speed.Range: 0.01Hz-20Hz
Trigger
Controls how the LFO behaves when a new key is being pressed.When not activated the LFO is in free run.
When activated the LFO will restart when a new note is being triggered.
Range: On/Off
Portamento
Parameters
Portamento On/Off
Turns the portamento on or off.Range: On/Off
Speed
Sets the portamento speed.Range: 0-1
Trigger Mode
Parameters
Trigger
Controls how the envelope generators behave when a new note is being triggered.When not activated the envelope generators are only re-trigged when a new key is being pressed and no other key is being held down .
When activated the envelope generators will be re-trigged when a new key is being pressed or when the latest key that was pressed down is released.
Range: On/Off
Midi
Pitch Bend
Parameters
Osc1
Sets the pitch bend range for oscillator 1.Range: ▒24 Semitones
Osc2
Sets the pitch bend range for oscillator 2.Range: ▒24 Semitones
Osc3
Sets the pitch bend range for oscillator 3.Range: ▒24 Semitones
Cutoff
Controls how much the Pitch Bend affects the cutoff frequency.Range: ▒100%
Mod Wheel
Parameters
Osc1 Mod
Controls how much the Mod Wheel will affect the LFO modulation of the oscillator frequency.Range: 0-100%
Osc2 Mod
Controls how much the Mod Wheel will affect the LFO modulation of the oscillator frequency.Range: 0-100%
Osc3 Mod
Controls how much the Mod Wheel will affect the LFO modulation of the oscillator frequency.Range: 0-100%
Cutoff
Controls how much the Modulation Wheel affects the cutoff frequency.Range: ▒100%
Velocity
Parameters
Curve
Sets the velocity curve.Off/Lin/Log
Cutoff
Controls how much the velocity will affect the cutoff frequency.Range: ▒100%